Bmw K 1100 LT/RS Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Motocykle Bmw K 1100 LT/RS. BMW K 1100 LT/RS User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - Repair Manual

BMW AG Motorcycle DivisionAfter SalesK 1100 LT/RSRepair Manual

Strona 2

00.2Contents PageChecking function of electric switch on side stand and adjusting if necessary ...

Strona 3 - Introduction

12.14Alternator [LT from 1992 model year on, RS]•Remove fastening screws (1) from cover.•Release clips (2) and take off cover.•Remove voltage regulato

Strona 4

12.15Checking alternatorL Note:Before measuring the resistance with the BMW di-agnostic tester, this must be zeroed:Connect the positive (yellow) and

Strona 5 - (from 1993 onlys)

12.16Removing and installing starter•Remove control unit.•[ABS I] Remove control unit.•[ABS II] Drain front and rear brake systems.•[ABS II] Remove pr

Strona 6

12.17Disassembling and assembling starter•Clamp starter at retaining lugs in vice with jaw guards.•Release retaining bolts (1).•Detach bearing cap (2)

Strona 7 - Contents

12.18Removing and installing brush holder1. Hexagon nut2. Outer insulator3. Carbon brush holder4. Brush retaining plate5. O-ring6. Inner insulator LT1

Strona 8

12.19Renewing carbon brushes•With the aid of a small screwdriver, lift spring (1) and pull out carbon brush.L Note:Fit carbon brush so that the chamfe

Strona 9

12.20Checking starter•Connect voltmeter between positive and nega-tive pole of battery.•Operate starter for 2...3 seconds.•Read off value.L Note:If th

Strona 10 - Contents Page

12.21Checking starter relay•Connect terminal 86 to positive battery terminal, terminal 85 to earth (ground).L Note:The relay is defective if no switch

Strona 11 - Tightening torque

12.22TroubleshootingTroubleshooting on alternatorAlternator makes noises.Do carbon brushes whistle?yesRework slip rings/replace carbon brushes. Batter

Strona 12

12.23Indicator lamp lights at only half brightness intensity when engine running.noCheck contacts of cable connections. Do cable connections have poor

Strona 13 - (with Loctite 243)

00.300Tightening torqueModel K 1100 LT K 1100 RSConnection Nm11 EngineFreewheelCover plate/freewheel cage at countershaft gear 10Oil – water pumpOil p

Strona 14

12.24Indicator lamp lights at half or full brightness with engine running. noCheck regulator.Is regulator defective?yesRenew regulator. noCheck supply

Strona 15

12.25Indicator lamp does not light when engine is stationary and ignition switched on. noCheck indicator lamp.Is lamp defective?yesReplace indicator l

Strona 16

12.26Troubleshooting on starterStarter does not turn when start switch is operated.noSwitch on light. Does light operate?noCheck battery.Is battery di

Strona 17

12.27Starter does not turn when start switch is operated.noSwitch on light. Does light operate?yesConnect jumper at connection between termi-nal 50 an

Strona 18 - Table of operating fluids

12.28Starter turns too slowly, does not crank en-gine.noCheck battery voltage.Is battery voltage too low?yesCharge battery, replace if necessary.noChe

Strona 19

12.29Troubleshooting on batteryBattery produces excessive gas.noCheck battery.Is battery defective?yesRenew battery.noCheck contact between regulator/

Strona 20

12.30Acid density too low.neinCheck charge status of battery.Is battery discharged?yesCharge battery.noCheck acid concentration.Is acid concentration

Strona 21

12.31Insufficient power outputnoCheck connection terminals.Are terminals loose/oxidated?yesClean/tighten terminals.noCheck acid level.Is level below t

Strona 23 - LT000140

13.1Contents Page13Technical data...

Strona 24 - Renewing brake fluid

00.4Timing chainChain tensioner 9Slide rail at camshaft bearing cap 9Timing case coverTiming case cover 10 (3-Bond 1209)Cover for Hall-effect signal t

Strona 26 - LT000180

13.313Technical data K 1100 LS K 1100 RSInside ø of throttle stub pipemm (in) 35 (1.37795)CO value % by vol. 1,5 ± 0,5 Idle speed rpm 950 ± 50

Strona 28 - LT000210

13.5Adjusting idle speedL Note:The basic setting (ignition, valve clearance) must be correct.•Remove knee pad.•Remove left side fairing.•Remove protec

Strona 29

13.6Checking start speed increase (choke), adjusting if necessaryChecking start speed increase•Remove left battery cover.•Set speed increase to limit

Strona 30

13.7Adjusting CO valueL Note:Engine must be at operating temperature (85 °C).Basic settings (ignition timing, valve clearances) must be correct.•Inser

Strona 31

13.8Removing/installing and checking/adjusting throttle position sensorRemoving and installing throttle posi-tion sensor•Unscrew the throttle position

Strona 32 - Slightly raise plate (2)

13.9Removing and installing air cleaner insert•Remove both knee pads.•Remove fuel tank.•Remove left and right heat-insulating bulkhead.•Release front

Strona 33 - LT000280

13.10Removing and installing air cleaner housing•Remove both knee pads.•Remove fuel tank.•Remove left and right side fairings.•Remove intake air guide

Strona 34 - LT000300

13.11•Loosen and pull off oil return pipe (5).•Loosen and pull off air return pipe (6).•Pull top section of air cleaner housing (7) out to the right.•

Strona 35 - 11 Motor

00.513 Fuel preparation and controlInjection rail 9Intake stub pipe 9Lower section of air cleaner housing 21Intake air line 9Motronic control unit 517

Strona 36

13.12Removing and installing throttle rail•Remove fuel tank.•Remove left fairing side section.•Remove left-hand heat-insulating bulkhead.•Release fuel

Strona 37

13.13Removing and installing injectors•Release wire retainer (1) and detach plug (2).•Release clip (3) at the injector and pull it out.•Install in the

Strona 38

13.14Removing and installing Motronic control unite Caution:Disconnect earth (ground) lead at battery!•Release multiplug (1) and disconnect.•Detach Mo

Strona 39

16.1Contents Page16Technical data...

Strona 41 - ±0.031 (0.0012)

16.316Technical data K 1100 LT K 1100 RSFuel tankTank capacity l (Imp.gal) 22 (4.84)incl. reserve capacity l (Imp.gal) 5 (1.1)Fuel pumpType Roller-cel

Strona 43 - -0.004 (0.0002)

16.5Removing and installing fuel tank•Open seat.•Remove left/right knee pads.•Remove retaining clips (1).•Release fuel line (2) at fuel tank.•Release

Strona 44

16.6Removing and installing fuel filter•If necessary reduce fuel level with pump until fil-ter is accessible.•Loosen hose clip (1) and slide towards f

Strona 45 - LT110840

16.7Removing and installing fuel level sensor•Removing and installing fuel level sensor•Remove and empty fuel tank.•Remove filler neck.•Release electr

Strona 46 - 11 0 610

00.623 TransmissionTransmission cover to transmission 9Machine screw for neutral stop 13Stud bolt, selector shaft 17 (Loctite 243)Transmission to inte

Strona 47 - Removing intermediate flange

16.8Removing and installing fuel pump•Remove and empty fuel tank.•Remove filler neck.•Release electrical connections (1/2) at the fuel pump.•Release h

Strona 48 - 33 1 830

16.9Checking fuel pump pressure•Connect test pressure gauge, BMW No. 16 1 500, on the delivery side.•Run engine at idle speed.Fuel pressure:Nominal va

Strona 50 - 00 5 010

17.1Contents Page17Technical data...

Strona 52

17.317Technical data K 1100 LT K 1100 RSCooling system capacity l(Imp.gal) 3.0 (0.66)+ 0.4 (0.088) in expansion tankCoolantAntifreezeWater%%Concentrat

Strona 54 - LT110790

17.5Changing coolantDraining coolant•Remove fuel tank.•Release cap (1) on filler neck. • [RS] Remove lower section of fairing •Release screw plug (2)

Strona 55 - LT110250

17.6Removing and installing thermostat•Remove fuel tank.•Remove right side section of fairing.•Remove radiator cowling.•Remove cover (1).•Pull out the

Strona 56 - LT110270

17.7Removing and installing radiator•Remove fuel tank.•[RS] Remove bottom section of fairing •Remove left/right side fairing.•Remove radiator cowling.

Strona 57 - LT110310

00.732 SteeringClamping screws for handlebar fitting 5Clamping screws 22Clamping block to fork bridge 1633 Rear wheel driveThreaded ring 118 (clean th

Strona 58 - LT110320

17.8Removing and installing fan•Remove radiator.•Remove rubber ring (1) and spacer bush (2).•Release retaining bolts (3, 4).•Install in the reverse or

Strona 59 - Removing crankshaft

17.9Removing and installing coolant hoses•Remove fuel tank.•[RS] Remove bottom section of fairing .•Remove left/right side fairings.•Remove correspond

Strona 60 - LT110360

17.10Checking cooling systemChecking cap for filler neck•Remove fuel tank.•Connect adapter (1), BMWNo.170003, to pump, BMWNo.170500. •Screw cap onto

Strona 61 - LT110400

17.11TroubleshootingCoolant temperature warning lamp lights up.noCheck coolant in expansion tank.Is coolant level too low?yesTop up coolant.noCheck th

Strona 62

17.12Übermäßiger Kühlmittelverlust.noCheck coolant circuit.Has coolant circuit a break?yesRepair break.

Strona 63 - LT110422

18.1Contents Page18Removing and installing exhaust system ...3Removing and instal

Strona 65 - Removing output shaft

18.318Removing and installing exhaust system•Release mounting (1) on cylinder head.•Release mounting (2) on transmission.•Release mounting (3) on foot

Strona 66 - LT110460

18.4Removing and installing oxygen sensor•Separate plug connection for oxygen sensor.•Remove left footrest plate.•Unscrew oxygen sensor at hexagon.L N

Strona 67 - LT110500

21.1Contents Page21Technical Data ...

Strona 68 - Installing output shaft

00.834 BrakesABS pulse wheel 4ABS sensor front/rear 4Brake caliperto sliding tube/rear wheel drive 40Brake line to brake caliper 18Bleed screws at bra

Strona 70

21.321Technical Data K 1100 LT K 1100 RSType of clutch Single dry plate clutch with diaphragm springOutside-ø of diaphragm springmm (in) 180 (7.0866)

Strona 72

21.5Removing clutch•Secure lifting gear, BMW No. 00 1 510, to the oil sump.•Remove main stand.•Remove rear mudguard.•Remove right-hand footrest plate.

Strona 73 - 11 2 925

21.6•Release housing cover (2).•Remove clutch disc (3), pressure plate (4), diaphragm ring (5) and wire ring (6).LT210060654231

Strona 74 - 11 2 210

21.7Removing clutch housing•Secure retaining fixture?(1), BMW No. 11 2 800, as shown.•Release hexagon nut (2).•Remove thrust ring (3) with pliers.•Mov

Strona 75

21.8Installing clutch housing•Coat tapers in clutch housing with Optimoly MP 3 or similar.•Fit thrust washer (1) on the clutch housing.•Using retainin

Strona 76

21.9Installing clutch•Grease all lubrication points with Optimoly MP 3.Lubrication points:Contact surfaces of pressure plate/diaphragm spring, wire ri

Strona 77

21.10•Release lower retaining bolt (1) of the ignition coil mounting.•Secure centring fixture (2), BMW No. 21 2 670, to intermediate flange.•Centre dr

Strona 78

21.11Adjusting clutch clearance•Detach clutch cable at the clutch release lever (1). •Slightly pull back rubber gaiter (2).•With the aid of setting ga

Strona 79

00.946 FrameFrame to engine 45Fairing support bracket to frame 9Suspension strut to frame/rear wheel drive 51Handlebar to clamping block 22Clamping sc

Strona 80

21.12Removing and installing clutch thrust bearing •Remove rear wheel.•Remove exhaust system.•Detach clutch cable at clutch release lever (1). •Loosen

Strona 81

21.13Removing and installing clutch con-trol rod•Remove rear wheel.•Remove exhaust system.•Remove clutch thrust bearing.•Remove clutch control rod (1)

Strona 82

21.14Removing and installing clutch release lever•Remove exhaust system.•Detach clutch cable at clutch release lever.•Remove retaining ring (4) and wa

Strona 83

21.15TroubleshootingClutch slips.noCheck clutch clearance.Is clutch clearance incorrect?jaAdjust clutch clearance. Replace clutch disc if necessary. n

Strona 84

21.16Clutch operation difficult.Clutch too harsh?noCheck output shaft lubrication. Is output shaft not lubricated?yesLubricate with Optimoly MP 3.

Strona 85 - LT110780

23.1Contents Page23Technical Data ...

Strona 86 - LT110800

23.2Contents PageDisassembling and assembling output shaft ...17Removing ball bearing

Strona 87 - 12 Engine electrics

23.323Technical Data K 1100 LT K 1100 RSType of gearshift5-speed transmission with dog-clutch engage-ment and integrated damper for all gearsType of g

Strona 89

23.5Removing transmission (gearbox)Preparatory work•[RS] Remove left fairing side section .•Remove exhaust system.•Disconnect CAT plug connection for

Strona 90

00.10Table of operating fluidsItem Use Order number QuantityLubricantOptimoly MP 3 High-performance lubricating paste 07 55 9 062 476 100 g tubeOptimo

Strona 91

23.6Removing starter•Release positive and negative lead at starter.•Release mounting.•Pull out starter. LT230410

Strona 92 - LT120030

23.7Removing bearing mount with main stand•Secure lifting gear, BMW No. 00 1 510, to the oil sump and slightly raise engine.•Release mounting for main

Strona 93

23.8Removing transmission (gearbox)•Release retaining bolts.•Screw guide pins, BMW No. 23 1 820, in holes with fitted sleeve, long pin on right-hand s

Strona 94

23.9Disassembling transmission (gear-box)Removing transmission cover.•Secure gearbox with holder (arrow “A”), BMW No. 23 1 600, to assembly stand.•Eng

Strona 95 - LT120060

23.10Disassembling/assembling transmis-sion coverRemoving and installing bearing shell•Heat bearing cover to 100 °C. •Remove bearing shell with Kukko

Strona 96

23.11Removing gear selector drum•Remove shafts (1) of gearshift forks.•Press pawl (2) towards the outside and secure with clamping fixture (arrow), BM

Strona 97

23.12Removing transmission shafts•Heat bearing seat of input shaft (1) and the inter-mediate shaft (2) to 100 °C.•Pull out both shafts together.•Remov

Strona 98 - LT120110

23.13Removing selector shaft•Release setscrew (arrow) (secured with Loctite).•Pull out selector shaft together with gearshift le-ver.Removing segment•

Strona 99 - LT120140

23.14Removing and installing shaft sealing ring for gear selector drum•Switch for gear indicator removed.•Gear selector drum removed.•Lever out shaft

Strona 100 - X Tightening torque:

23.15Disassembling and assembling input shaftDisassembling input shaft•Clamp spline end of input shaft in vice with jaw guard.•Remove retaining ring (

Strona 101 - 61 1 510

00.11Key to maintenance intervals – Inspection at 1000 km (600 miles)I– BMW Service at 10,000 km (6000 miles))II– BMW Inspection at 20,000 km (12,000

Strona 102 - X Tightening torques:

23.16•Fit universal puller under the spur gear and pull down taper roller bearing as far as it will go on the retaining ring.L Note:There must be no c

Strona 103 - LT120160

23.17Disassembling and assembling output shaft •Before disassembling, measure axial clearance of spur gear for 1st, 2nd and 5th gears.1st gear ... 0

Strona 104 - LT120170

23.18Removing spur gears•Remove spur gear for 1st (1) and 5th gear (2) with spacer shim rings.•Heat bearing bush (4) to 80 °C.•Carefully remove spur g

Strona 105 - brushes

23.19Installing spur gears•Slide serrated washer (10) over smooth end (ar-row) onto output shaft up to the bearing seat.•Slide on retaining ring (11)

Strona 106 - Checking starter

23.20Installing transmission shafts•Heat bearing points for intermediate shaft and output shaft in the housing to 80°C.•Fit input shaft.•Install inter

Strona 107 - LT120210

23.21Measuring distances between trans-mission shaftsMeasuring bearing distance of shafts•Place transmission measuring plate, BMW No. 23 3 660 (arrow)

Strona 108 - Troubleshooting on alternator

23.22Measuring transmission cover•Measure from the parting surface of the trans-mission cover to the base of the bearing seat.•Only applies to interme

Strona 109

23.23Measuring distances between transmission shaftsExample:•Remove measuring plate from transmission housing.•Fit calculated spacer shim rings on the

Strona 110

23.24Installing transmission cover•Knock out cap (arrow) from the inside using a drift.•Heat up transmission cover to 100°C.•Parting surface at housin

Strona 111

23.25Installing transmission (gearbox)•Clutch thrust bearing must be removed.•Check centre position of driving disk.•Coat spline of input shaft, for e

Strona 112 - Troubleshooting on starter

Published by BMW AG Motorcycle DivisionAfter SalesUX-VS-2All rights reserved. Not to be reprinted, translated or duplicated either wholly or in part w

Strona 113

00.12Changing oil in rear wheel driveInspections I, III, IV•Drain off oil with drive at operating temperature.•Oil drain plug (1)•Oil filler plug (2)L

Strona 114

23.26Installing bearing mount with main standL Note:Clean threaded holes in transmission and retaining bolts (recut thread).•Place switch (1) for elec

Strona 115 - Troubleshooting on battery

23.27Installing starter•Connect positive and negative leads.X Tightening torque:Positive lead... 5 NmSt

Strona 116

23.28Re-assembling motorcycle•Install battery.•Intall Motronic control unit.•[ABS II] Install ABS unit.•Install battery.•Intall Motronic control unit.

Strona 117

31.1Inhalt Seite31Technical Data ...

Strona 119

31.331Technical Data K 1100 LT K 1100 RSFront wheel castor mm (in) 95 (3.74)Steering angle °34Spring travel (normal position, 75 kg load) mm (in) 135

Strona 121 - Idle speed rpm 950 ± 50

31.5Removing telescopic fork•Secure lifting gear, BMW No. 00 1 510, to oil sump.•Remove fuel tank.•Remove front mudguard.•Remove brake caliper.Removin

Strona 122

31.6Removing and installing lower taper roller bearingRemoving taper roller bearing•Press down steering tube (1) by approx. 5 mm and press back again.

Strona 123 - Adjusting idle speed

31.7Removing and installing bearing outer race in steering headRemoving bearing outer race•Remove bearing outer race (1) using extractor BMW No. 00 5

Strona 124 - Retighten locknut (3)

00.13Renewing fuel filterInspection III•If necessary, reduce fuel level with pump until fil-ter is clear.•Loosen hose clip (1) and shift towards filte

Strona 125 - Caution:

31.8Measuring telescopic forkL Note:After a collision, the telescopic fork must be exam-ined for cracks and damage.Checking lower fork bridge•Clamp fo

Strona 126 - LT130060

31.9Checking parallel alignment of fixed tubes•Clamp fork bridge at steering tube in vice with jaw guards.•Install upper fork bridge.L Note:Fork bridg

Strona 127 - LT130070

31.10Checking runout of fixed tube•Place both ends of stanchion in V-blocks.•Slowly turn fixed tube while checking dial gauge.e Caution:Distorted fixe

Strona 128 - LT130080

31.11Disassembling telescopic forkRemoving fixed tube•Loosen clamping screws at lower fork bridge.•Remove fixed tube with slider tube from fork bridge

Strona 129

31.12Disassembling fixed tube•Loosen screw plug (1) in fixed tube.•Screw base screw fitting (arrow) loosely into damper cartridge.•Lightly press dampe

Strona 130 - LT130110

31.13•Press apart plain bush (8) on the fixed tube (arrows) and remove.•Slightly preform new plain bush in order to achieve an optimum fit on the fixe

Strona 131

31.14Assembling telescopic forkAssembling fixed tube•Fit fork support spring (6) on damper cartridge (5), small winding spacing at top.•Fit guide slee

Strona 132

31.15•Fit spacer sleeve (4).•Fit perforated disc (3), smooth side facing down-ward.•Fit retainers (2) and relieve clamping fixture.•Screw in screw plu

Strona 133 - 16 Fuel tank and lines

31.16Assembling slider tube•Install damper cartridge with hole pattern “Z” (tension stage) in the right-hand slider tube.•Install plain bush (1) lubri

Strona 134

31.17Installing telescopic fork•Grease taper roller bearing with Shell “Retinax A” or similar.•Fit telescopic fork from below into steering head.•Inst

Strona 135 - Make Bosch

00.14Checking brake pads, brake discs for wear and renewing if necessaryInspection II, III Front wheel brake•Remove rear section of mudguard.•Remove b

Strona 136

31.18Adjusting steering bearing play•Fit a piece of adhesive tape (arrow) on the fork bridge above the setting ring.•Mark current position of the sett

Strona 137 - LT160010

31.19Installing fork stabilisor•Install fork stabilisor, handtighten screws.•Install brake distributor (1).•Lay ABS sensor line (2) and connect. •Inst

Strona 139 - LT160030

32.1Contents Page32Technical Data ...

Strona 141 - 16 1 500

32.332Technical Data K 1100 LT K 1100 RSSteering anglel °2 x 34Steering tube-ø mm (in) 22 (0.86614)Handlebar width with weights mm (in) 765 (30.11805)

Strona 143 - 17 Radiator

32.5Removing and installing left and right handlebar fittingsRemoving and installing left handlebar fitting•Remove fuel tank.•[LT] Cut through cable c

Strona 144

32.6•Cut open rubber grip (1) and remove.•Release multifunction switch (2).•Loosen clamping screw (3) of handlebar fitting.•Remove fitting from handle

Strona 145

32.7Removing and installing right handle-bar fitting•Remove fuel tank.•[LT] Cut through cable clip (1).•Disconnect plug connection (2) for brake light

Strona 146

00.15Checking brake fluid level and cor-recting if necessaryInspections I, II, IIIChecking brake fluid levelL Note:When checking front brake fluid lev

Strona 147

32.8Removing and installing handlebar•Remove fuel tank.•Remove handlebar cover (1).•Disconnect plug connections for switches.•Remove left and right ha

Strona 148

32.9Removing and installing handlebar clamping blocks•Remove stop plate (3).•Remove clamping blocks (4).•Drive out handlebar mounting with drift.•Inst

Strona 149

32.10Removing and installing accelera-tor cable•Remove fuel tank.•Remove cable cover (1) on handlebar fitting.•Detach cable.•Turn in cam disc on throt

Strona 150 - Removing and installing fan

32.11Removing and installing clutch cable•Remove fuel tank.•Detach clutch cable (1) at clutch release lever.•Pull clutch hand lever and press out nipp

Strona 151

32.12Removing and installing operating cable for increasing starting speed•Remove fuel tank.•Remove operating lever (1).•Detach cable (2).•On throttle

Strona 152 - LT170090

32.13Adjusting steering bearing play•Fit a piece of adhesive tape (arrow) on the fork bridge above the setting ring.•Mark current position of setting

Strona 154

33.1Contents Page33Technical data...

Strona 156

33.333Technical data K 1100 LT K 1100 RSRear wheel driveType of gearingKlingelnberg Palloid spiral bevelNumber of teeth 32 : 11Gear ratio 2.91 : 1Toot

Strona 157 - X Tightening torques :

00.16Renewing brake fluidRenewing front brake fluid•Remove the break padse Caution:Do not tilt the brake caliper when removing or install-ing, or the

Strona 159 - 21 Clutch

33.5Removing, disassembling, assem-bling and installing rear wheel drive•Remove licence plate bracket.•Remove rear wheel.•Remove brake disc, mark posi

Strona 160

33.6•Screw the rear wheel drive centrally with holder, BMWNo.331510, and bearing journal (1).•Screw on locking arm (3).•Move threaded bushings (5) int

Strona 161

33.7Disassembling drive bevel gear•Remove outer bearing race (2).•Remove spacer ring (3) from housing.•Clamp drive bevel gear (1) in vice with jaw gua

Strona 162

33.8Removing needle bearing for drive bevel gear•Destroy needle cage of needle bearing.•Heat housing to 130 °C.•Remove outer race of needle bearing wi

Strona 163 - 00 1 510

33.9Assembling drive bevel gear•Heat inner race (4) to 100 °C and slide onto drive bevel gear (1) as far as it will go.•Slide outer bearing race (2) t

Strona 164 - Release housing cover (2)

33.10Installing drive bevel gear•Drive sealing ring (2) into threaded rim (3) with the aid of drift, BMW No. 33 1 760, and retainer, BMWNo.005550. •He

Strona 165 - , and pressure tool

33.11Removing and installing taper needle bearing in rear wheel drive•Remove needle bearing using inner extractor21/4, BMW No. 00 8 573, and support 2

Strona 166

33.12Removing crown wheel•Remove housing cover (1) with crown wheel (2) and bearing (3). •Heat housing cover (1) to 100 °C and remove.•Drive shaft sea

Strona 167 - LT210010

33.13•Remove taper roller bearing from ring gear with puller, BMWNo.007500.•Remove outer bearing race with internal extrac-tor, BMW No. 00 8 560.Insta

Strona 168

00.17Checking function of electric switch on side stand and adjusting if nec-essaryInspections I, II, III•Place motorcycle on centre stand on even sur

Strona 169 - LT210080

33.14Checking/adjusting tooth backlash•Lock drive bevel gear in position with 36 mm (1.4173 in) insert, BMW No. 33 1 720. •Fit measuring ring, BMW No.

Strona 170 - LT210100

33.15Checking contact pattern•The contact pattern must be checked when the set of gears, the housing or the bearing of the drive bevel gear has been r

Strona 171 - LT210110

33.16Shimming housing cover•The housing cover must be shimmed in order to achieve the corresponding preload of the taper roller bearing.•Measure dista

Strona 172

33.17Installing rear wheel drive•Coat spline on sliding piece (arrow), for example with Optimoly MP3.•Fit inner race (5) of right-hand needle bearing

Strona 173

33.18•Apply a load of approx. 85 Kg (1887.43 lb)to the motorcycle and tighten loose strut (4) with the nut on the wheel side.X Tightening torques:Stru

Strona 174

33.19Removing, disassembling and assembling rear swinging arm•Remove left and right footrest plate.•Heat to max. 120 °C at loose bearing of swinging

Strona 175 - 23 Gearbox

33.20Removing and installing gaiter•Remove inner retaining ring, pull gaiter out of swinging arm.•Install in the reverse order of removal.•Coat inside

Strona 176

33.21Installing swinging arm•Slide swinging arm over drive shaft.•Lift drive shaft over the support surface in the swinging fork and press forward swi

Strona 178

34.1Contents Page34Technical Data ...

Strona 179 - Preparatory work

00.18Checking clutch clearance and adjusting if necessaryInspections I, III•Detach clutch cable at clutch release lever (1).•Slightly push back rubber

Strona 180 - Removing starter

34.2Contents Page[ABS II] Installing ABS unit ...

Strona 181

34.334Technical Data K 1100 LT K 1100 RSBrake fluid DOT 4Minimum brake pad thickness mm (in) 1.5 (0.059)Front wheelBrake disc Ø mm (in) 305 (12.01)Bra

Strona 183 - LT230010

34.5Removing and installing front brake caliper•Mask off brake caliper at top of wheel side with tape (rim guard).•Release brake caliper mounting (1)

Strona 184 - LT230050

34.6Dismantling and assembling front brake calipere Caution:The brake caliper halves must not be unscrewed!Dismantling front brake caliper•Remove the

Strona 185 - Note sleeves on guide pins

34.7Assembling front brake caliper•Coat new sealing rings (3,4) with brake fluid and install. •Coat brake caliper pistons (2) with brake fluid and ins

Strona 186 - LT230100

34.8Removing and installing brake pads•Remove brake caliper.L Note:If only the brake pads are to be replaced, do not re lease the brake line at the br

Strona 187

34.9Removing and installing front brake disc•Remove front wheel.•Release retaining screws (1) for brake disc carri-er.•Detach brake disc carrier (2) w

Strona 188 - LT230160

34.10Removing and installing front ABS sensor•Remove fuel tank.•Disconnect plug connection (1) of sensor line.•Remove cover for brake distributor.•Rem

Strona 189 - LT230190

34.11Adjusting front ABS sensor gap•Raise front wheel with front wheel stand, BMW No. 36 3 950.•Secure dial gauge holder (1), BMW No. 34 2 520 with di

Strona 190 - 00 7 500

00.19Checking increased starting speed (choke) and adjusting if necessaryInspections I, IIIChecking increased starting speed•Remove the left battery c

Strona 191 - LT230220

34.12Removing and installing front brake lineRemoving upper brake line•Drain brake system.•Remove fuel tank.•Release brake line (1) at handbrake cylin

Strona 192 - LT230250

34.13Removing and installing ABS brake line from front pressure modulator•Remove knee pads.•Remove fuel tank.•Release screw connections (1,2).•Release

Strona 193 - LT230280

34.14Removing and installing handbrake cylinder•Drain brake system.e Caution:Ensure brake fluid does not come in contact with painted parts of the veh

Strona 194 - LT230300

34.15Bleeding brakee Caution:Escarping brake fluid can damage painted surfaces.Bleeding front brakeBleeding brake caliper•Remove front brake pads.e Ca

Strona 195 - 00 2 550

34.16[ABS II] Bleeding pressure modulator•Remove the left battery cover.•Connect a vessel to the brake caliper bleed screws to trap escaping brake flu

Strona 196

34.17Removing and installing pressure modulatore Caution:Work on the ABS unit is only to be carried out by an authorised BMW workshop.[ABS I] Removing

Strona 197

34.18[ABS II] Removing ABS unit•Remove the dualseat.•Remove the left and right battery trim panels.•Remove the Motronic control unit.•Remove the batte

Strona 198

34.19[ABS II] Installing ABS unit•Install ABS unit (6).•Reconnect central plug (5).e Caution:Do not tilt the cables or the insulation may be dam-aged.

Strona 199

34.20[ABS II] Removing and installing relay and relay base[ABS II] Removing relaye Caution:Switch off the ignition and disconnect and insulate the ear

Strona 200

34.21•Install a new cover (1).e Caution:When pushing on, make sur that all cables are cor-rectly located in their guides. Scrap the old cover.[ABS II]

Strona 201

00.20Checking valve clearance and adjusting if necessaryInspections I, IIIe Caution:Never unscrew the spark plugs before measuring the valve clearance

Strona 202

34.22Removing and installing rear brake caliper•Drain brake System.•Release bottom of suspension strut (1).•Detach suspensions strut from stud bolt.•R

Strona 203 - 31 Front fork

34.23Dismantling and assembling rear brake caliperDismantling rear brake caliper•Remove keepers (1).•Drive out spring (2) and retaining pin (3). •Take

Strona 204

34.24Removing and installing rear brake disc•Remove brake caliper.•Remove rear wheel.•Remove brake disc.L Note:Mark installation position of the brake

Strona 205

34.25Removing and installing rear ABS sensor•Remove brake caliper but do not loosen brake line.•Release sensor with socket wrench, BMW No. 00 2 640.•D

Strona 206

34.26Measuring vertical runout at rear pulse wheel•Remove brake caliper.•Remove rear wheel.•Secure dial gauge with retaining fixture to bottom of spri

Strona 207 - LT310020

34.27Removing and installing rear master brake cylinder•Drain brake system.e Caution:Ensure brake fluid does not come in contact with painted parts of

Strona 208 - LT310040

34.28Disassembling rear master brake cyl-indere Caution:Piston is under spring loading.•Using thrust piece (1), push piston (2) a little way inwards.•

Strona 209 - LT310060

34.29Removing and installing brake pedal•Remove footrest plate.•Detach sealing gaiter (1) at master brake cylin-der.•Release mounting (2) for brake pe

Strona 210 - 31 4 620

34.30Adjusting foot brake pedal•Loosen locknut (1).•Perform basic setting with adjusting screw (2).•Adjust distance „A“ with feeler gauge.Basic settin

Strona 211 - LT310090

34.31Troubleshooting: Front wheel/rear wheel brakeBrake rubs/vibrates.noCheck brake pads.Are brake pads worn/damaged?yesRenew brake pads.Brake pedal s

Strona 212 - LT310100

00.21L Note:Only the bucket tappets replaced during the 1000 km (600 miles) inspection can be re-used.Installing camshafts•The camshafts are marked to

Strona 213 - LT310120

34.32Reduced brake effect when applied hard?noCheck brake fluid.Has brake fluid aged?yesRenew brake fluid.Only mederate brake effect?noCheck brake pad

Strona 214 - LT310150

34.33Brakes rubbing.noCheck hydraulic system.Is there a defect in hydraulic system operation?yesRectify defect.noCheck brake piston.Are brake pistons

Strona 216

36.1Contents Page36Technical Data ...

Strona 218

36.336Technical Data K 1100 LT K 1100 RSRim size front 2.50 x 18 MT H 2 3.50 x 17 MT H 2rear 3.00 x 17 MT H 2 4.50 x 18 MT H 2Vertical runout mm (

Strona 220

36.5Removing and installing front wheel•[RS] Raise the front wheel with the front wheel stand, BMW No. 36 3 950.•[LT] Raise the front wheel with the f

Strona 221

36.6Removing and instaling wheel bearings•Place the wheel on two wooden blocks so that the brake disc is free.Removing left bearing•Take out circlip (

Strona 222

36.7Removing and installing rear wheelRemoving rear wheel•Remove number plate bracket.•Remove the brake caliper.•Pull off cap (1) with an angled screw

Strona 223 - 32 Steering

IntroductionThis repair manual will help you to perform all the main maintenance and repair work correctly and efficient-ly. If it is consulted regula

Strona 224

00.22Installing cylinder head cover•Screw fitted bolt, BMW No. 11 1 980, (arrow) into inner hole at the front.•Press centring pin, BMW No. 11 1 990, w

Strona 225 - Steering anglel °2 x 34

36.8Static balancing of front and rear wheelsStatic balancing of front wheel•Remove the wheel.•Insert the balancing shaft, BMW No. 36 3 614, through t

Strona 226

36.9Checking wheel for runoutChecking front wheel for runout•Install the wheel without tyre on the balancing shaft, BMW No. 36 3 614, and balancing st

Strona 228

46.1Contents Page46Technical Data ...

Strona 229

46.2Contents PageChecking frame with gauge ...18Rem

Strona 230

46.346Technical Data K 1100 LT K 1100 RSLocation of type identification plate Rear right frame tubeLocation of chassis number Rear right frame tubeMax

Strona 232 - LT320080

46.5Removing and installing front mudguard•Loosen clamping screws (1,2).•Detach cover (3).•Remove rear section of mudguard (4).•[LT] Detach Velcro con

Strona 233 - Adjust cable after fitting

46.6Removing and installing rear sec-tion•Remove dualseat.•Remove combined tail light unit.•Release securing screw (1).•Install in the reverse order o

Strona 234 - LT320100

46.7Removing and installing rear mudguard1. Rubber sleeves on gearbox2. Bracket3. Sheet-metal nuts4. Licence plate support bracketLT4900403421

Strona 235

00.23Checking steering bearing play and adjusting if necessaryInspection III•Place a piece of adhesive tape (arrow) on the fork bridge above the setti

Strona 236

46.8Removing and installing fairing [LT]Removing side sections of fairing•Remove knee pad (1).•Remove storage box (2).•Remove cover (3).•Remove side s

Strona 237 - 33 Rear wheel drive

46.9Removing and installing windshield•Release securing screws (1) on left and right and detach screen.Removing and installing windshield complete wit

Strona 238

46.10Disassembling and assembling adjust-able windshieldRemoving and installing actuator motor•Release securing elements (1) for actuator motor and re

Strona 239

46.11Removing lever•Remove actuator motor.•Remove plate.•Detach spring.•Release securing element (3) of guide rod (4), while holding with pin (5).•Pul

Strona 240

46.12Removing and installing upper section of fairing•Remove side sections of fairing and radiator cowling.•Remove cover (1).•Remove complete windshie

Strona 241 - LT330430

46.13Removing and installing fairing [RS]Removing and installing lower section of fairing– Lower section of fairing (1)•Release securing element on si

Strona 242 - RT330360

46.14Removing and installing upper section of fairing•Remove lower section of fairing, side sections and radiator cowling.•Remove cover (1).•Remove su

Strona 243

46.15Removing and installing fairing support bracket•Remove fairing.•[LT] Remove instrument cluster.•Remove horns (1).•Disconnect cable clips for wiri

Strona 244 - 00 8 573

46.16Checking running gearMeasuring track offset•Mount motorcycle on centre stand on even base.•Position track offset gauge (1), BMWNo.363920, on left

Strona 245 - LT330070

46.17•Calculate track offset ”S”:EXAMPLE:•The track offset ”S” represents the amount by which the longitudinal axis of the front wheel is offset to th

Strona 246 - X Tightening torquse:

00.24Lubricating guide pins, adjustable screenInspections III, IV•Release retaining screw (1) on both sides.•Slightly raise plate (2).•Spray guide pin

Strona 247 - 00 8 572

46.18Checking frame with gauge•Remove fairing.•Support motor cycle with lifting gear, BMWNo.001510.•Remove telescopic fork.•Outer bearing race at top

Strona 248 - LT330130

46.19•Fit measuring pins (1), BMW No. 46 5 602, lightly greased, in the outer holes.•Slightly loosen nut on steering head and align gauge so that the

Strona 249 - RT330170

46.20Removing and installing frameRemoving frame•Set motorcycle on centre stand.•Support with lifting gear, BMWNo.001510, un-der oil sump. •Remove sea

Strona 250 - RT330210

46.21Removing and installing seat lock1. Saucer-head screw2. Phillips-head screw3. Stop nutRemoving and installing handle•Lever out spring using screw

Strona 251 - Checking contact pattern

46.22Installing frame•Installation basically takes place in the reverse order of removal.•Place frame on drive train and firmly tighten screws and bol

Strona 252

46.23Removing and installing main centre stand•[RS] Remove lower section of fairing.•Raise motorcycle with lifting gear, BMW No. 00 1 510, under the o

Strona 253 - Tightening torques:

46.24Disassembling and assembling side standDisassembling side stand•Detach switch (1).•Detach tension springs (2).•Remove bracket (3) with spring.•Re

Strona 254 - Check sensor grap

46.25Assembling side standL Note:The securing screw of the side support is micro-en-capsulated and cannot be reused. Clean thread and holes. Coat scre

Strona 255 - LT330370

46.26Disassembling and assembling main centre stand •Detach tension springs (1).•Release screws (2) on left/right.•Release retaining ring (3).•Press o

Strona 256 - Installing drive shaft

46.27Checking switching function of side stand•Set vehicle on centre stand on even base or lift-ing platform.•Spray switching kinematics of side stand

Strona 257

00.25Checking idle speed, synchronising and CO value and adjusting if nec-essaryInspections I, II, III, IVL Note:The basic settings (ignition, valve c

Strona 259 - 34 Brakes

51.1Contents Page51Removing and installing ignition switch/steering lock ...3Removing and installing lock cyl

Strona 261

51.351Removing and installing ignition switch/steering lock•Remove fuel tank.•Disconnect plug connection (1) for ignition switch/steering lock.•Detach

Strona 262

51.4Removing and installing lock cylin-der for fuel tankRemoving lock cylinder•Open cover and release screws (1).•Remove housing (2) for lock cylinder

Strona 263

51.5Removing and installing dualseat lock5. Saucer-head screw6. Phillip-head screw7. Stop nutLT5100402113

Strona 265 - LT340280

61.1Contents Page61Technical Data ...

Strona 267

61.361Technical Data K 1100 LT K 1100 RSBatteryAh 19

Strona 268

00.26Adjusting CO value without catalytic converterL Note:Engine must be at operating temperature (85 °C).The basic settings (ignition, valve clearanc

Strona 270

61.5Removing and installing Motronic control unite Caution:Switch off ignition, disconnect and insulate earth (ground) lead!•Open dualseat.•Press catc

Strona 271

61.6[ABS I] Removing and installing control unite Caution:Switch off ignition, disconnect and insulate earth (ground) lead!•Switch off ignition, disco

Strona 272

61.7Removing and installing batterye Caution:Switch off ignition, disconnect and insulate ground lead!•Remove Motronic control unit.•[ABS I] Remove AB

Strona 273

61.8Relay locations (central electrical unit)•First remove the fuel tank in order to remove a relay.1. Lamp control unit2. Start relay3. Turn indicato

Strona 274

61.9Locations and connections, ABS wiring loomL Note:All ABS plug connections are blue.1. [ABS I] Multi-pin plug, ABS control unit2. [ABS I] Plug conn

Strona 275

61.10Locations, frame wiring loomView from leftL Note:When removing the wiring loom, also remove the central electrical box together with the wiring l

Strona 276 - LT340250

61.11View from right1. Right multi-function switch connection2. Ignition lock connection3. Handbrake light switch plug connection4. Hall generator plu

Strona 278 - LT340270

62.1Contents Page62Technical Data ...

Strona 279 - [ABS II] Removing relay base

11.1Contents Page11Technical data ...

Strona 281

62.362Technical Data K 1100 LT K 1100 RSInstrument clusterTurn signal indicator lamps 12 V/4 W T 8/4Other indicator lamps, instrument lights 12 V/3 W

Strona 283

62.5Removing and installing instrument cluster[LT]•Remove upper section of fairing.•Release screw (1) and disconnect central plug connector.•Release s

Strona 284

62.6[RS]•Remove upper section of fairing.•Release screw (1) and disconnect central plug connector.•Release screws (2) and remove instrument clus-ter.•

Strona 285

62.7Disassembling and assembling instrument cluster•Release instrument support bracket (1).•Release housing cover (2) and remove together with gasket

Strona 286 - LT340200

62.8Removing and installing p.c. board•Release securing screws and carefully lift out p.c. board (1).L Note:Do not damage p.c. board when removing and

Strona 287

62.9Removing and installing revolution counter•Release screws (1).•Lift out revolution counter (2).Removing and installing speedometer•Release screws

Strona 288

62.10Removing and installing p.c. board for gear indi-cator•Remove tachometer.•Carefully pull pointer (1) off the spindle.•Release screws (2).•Remove

Strona 289

63.1Contents Page63Technical Data ...

Strona 290

11.2Contents PageRemoving pistons with conrods, stripping down and re-assembling ...26Removing piston with conrod ...

Strona 292

63.363Technical Data K 1100 LT K 1100 RSLightsHeadlight Halogen rectangular headlight with two-stage manual range adjustmentBulbsHigh beam/low beam H

Strona 294

63.5Disassembling and assembling headlights•Remove upper section of fairing.•Remove headlight.•Release retaining spring (5).L Note:Do not touch the in

Strona 295

63.6Adjusting headlights •Engage swivel lever (1) in top position.•Correct headlight range with adjusting screw (2).•Turning counterclockwise: shorter

Strona 296

11.3Contents PageInstalling timing chain ...

Strona 298 - LT360030

11.511Technical data K 1100 LT K 1100 RSEngine, generalEngine design Inline four-stroke engine installed longitudinally, with double overhead camshaft

Strona 299 - LT360040

UsageEach chapter starts with the list of contents.The list of contents is followed by the Technical Data table.Chapter 00 “Maintenance and general in

Strona 300 - LT360050

11.6ValvesValve clearances with engine cold (max. 35 °C)Inlet valve mm (in) 0.15…0.20 (0.0059…0.0079)Exhaust valve mm (in) 0.25…0.30 (0.0098…0.0118)Va

Strona 301 - Checking wheel for runout

11.7ValvesValve guide dia.Extl. dia. mm (in) 11.533…11.544 (0.4541…0.4545)Intl. dia. mm (in) 6.0…6.012 (0.2362…0.2367)Wear limit mm (in) 6.1 (0.2402)B

Strona 302

11.8CrankshaftMain bearing and crankpin markingsno colour spot Grinding stage 0with colour spot Grinding stage 1Width of guide bearing mm (in) 23.020…

Strona 303 - 46 Frame

11.9Piston rings1st groove Rectangular-sectionHeight mm (in) 1.175…1.190 (0.0462…0.0469)Wear limit mm (in) 1.100 (0.0433)Ring gap mm (in) 0.20…0.40 (0

Strona 305 - mm (in) 12 (0.47)

11.11Removing engine•Remove fuel tank.•Remove knee pads.•Remove fuel tank.•Remove lower section of fairing at left and right.•Remove radiator surround

Strona 306

11.12Dismantling engine•Remove air cleaner box.•Remove fuel injection rail.•Remove throttle rail.•Attach engine mount, BMW No. 11 0 610, to the engine

Strona 307 - LT460020

11.13Removing intermediate flange•Remove alternator.•Remove coils with holder.Removing driver•To remove the screw, support the driver (arrow).•Pull th

Strona 308 - Release securing screw (1)

11.14Removing clutch housing•Install the retaining device (arrow), BMWNo.112800, in the position illustrated.•Unscrew hex nut (1) and take off thrust

Strona 309 - 3. Sheet-metal nuts

11.15Stripping down and re-assembling intermediate flangeRemoving the driver bearing•Bearing plate (1) •Cup spring (2) •Pull out ball bearing (3) with

Strona 310 - LT460060

Order No. 01 71 9 799 131 UX-VS-2, 12/98 Printed in GermanyCustomer Registration No.Order No. Signature of mechanicBMW Inspection 1000km/600mlsBMW Ser

Strona 311 - LT460070

11.16Removing and installing shaft sealing ring for driver•If the intermediate flange has been removed, le-ver out the sealing ring.•If the intermedia

Strona 312 - LT460090

11.17Dismantling and assembling freewheelStripping down freewheel•Pull freewheel gear (1) off layshaft (5).•Clamp the layshaft into a vice with soft j

Strona 313

11.18•Place the cup spring in position.•Insert the freewheel (oiled with engine oil) into the outer race.•Install the outer race (with clamp block fac

Strona 314 - LT460130

11.19Removing timing chain coverRemoving the Hall-effect signal transmitter•Remove cover (1).•Take off gasket (2).•Remove Hall-effect signal transmitt

Strona 315 - LT460150

11.20Removing the timing chain•Set cylinder 1 (timing end) to TDC, noting direc-tion of rotation (arrow). Pin (1) on the crankshaft must be aligned wi

Strona 316 - LT460170

11.21Removing camshaft chain sprockets•When taking out the retaining screws, hold the hexagon on the camshaft to prevent it from turn-ing.•Remove chai

Strona 317

11.22Removing, stripping down and assem-bling cylinder headRemoving camshafts•Remove the bearing caps (1) for the thrust bear-ings first, to prevent t

Strona 318 - LT460210

11.23Removing valves•Screw support plate, BMW No. 11 1 749, for the valve spring clamping tool on to the rear of the cylinder head.•Attach valve sprin

Strona 319 - LT460220

11.24Installing valve and valve stem sealL Note:If a valve was removed, the valve stem seal must be renewed.•Oil the stem when installing the valve.•I

Strona 320 - 46 5 600

11.25Removing crankshaftRemoving big end bearings•Move the piston in cylinders 1 and 4 to the bot-tom dead centre (BDC) position.•Remove the big end b

Strona 321 - 46 5 602

Order No. 01 71 9 799 131 UX-VS-2, 12/98 Printed in GermanyCustomer Registration No.Order No. Signature of mechanic BMW Pre-delivery checkInspect crat

Strona 322 - LT460280

11.26Removing pistons with conrods, strip-ping down and re-assemblingRemoving piston with conrod•Press the piston with conrod out from the crank-shaft

Strona 323 - LT510040

11.27Assembling pistons•Install piston rings, using piston-ring pliers.1st groove: rectangular-section ring2nd groove: micro-chamfer ring (note pinfor

Strona 324

11.28Assembling pistons and conrodsL Note:[LT] Modified conrod length and pistons from 1993 model year on•Comply with conrod weight tolerances.Weight

Strona 325

11.29Removing, dismantling and assem-bling combined oil-water pumpRemoving pump•Pull off the wires for the oil pressure and water temperature display

Strona 326 - Disassembling side stand

11.30Removing slipring seal and shaft sealing ring•Press out slipring seal (6) with a drift.•Using a 5 mm (0.2 in) wide screwdriver, carefully press o

Strona 327

11.31Removing output shaftRemoving oil sump•After removing the screws, loosen the seal with light blows of a plastic-faced hammer.Removing oil filter•

Strona 328 - LT460370

11.32Stripping and assembling output shaftStripping down output shaft•Take off needle roller race (1) and circlip (2).•Pull output shaft (3) out of da

Strona 329 - LT460380

11.33Assembling tensioning gear•Insert the tensioning spring.•Install tensioning gear with counter-holder, BMW No. 12 4 600.•Clamp the tensioning gear

Strona 330

11.34Assembling engineInstalling output shaft•Push circlip (1) and needle roller sleeve (2) on to the bearing point.•Place the output shaft in the cra

Strona 331 - 51 Equipment

11.35Assembling the crankcase•Install O-rings (6,7) for the water and oil passag-es.•Coat the sealing faces (which must be free from oil and grease) l

Strona 332

00 Maintenance and general instructions ... 00.111 Motor...

Strona 333

11.36Measuring crankshaft bearing playMeasuring radial play•Crankshaft bearing points must be clean and lightly oiled.•Place the crankshaft in the cra

Strona 334 - LT510030

11.37Measuring endplay•Install the crankshaft and measure as for radial play.•Screw measuring fixture,BMW No. 00 2 500, with dial gauge into the tappe

Strona 335 - 7. Stop nut

11.38Installing crankshaft•Oil the bearings lightly before inserting the crank-shaft.•Install the corresponding bearing caps with the grooves aligned.

Strona 336

11.39Installing piston with conrod•Turn the corresponding crankpin to bottom dead centre.•The piston ring gaps must be offset by app. 120° in each cas

Strona 337

11.40Measuring big end bearing play•Turn the crankpin 30° away from bottom dead centre.•Wipe oil off crankpin and bearing cap.•Place Plastigage strip

Strona 338

11.41Installing combined oil-water pump•Apply a thin coat of 3-Bond 1209 to the sealing faces, which must be free of oil and grease.•Place O-ring on w

Strona 339

11.42Installing cylinder head•Move the piston in cylinder 1 to top dead centre (cylinder 1 = timing end).•Place the cylinder head gasket in position;

Strona 340

11.43Installing camshaftsL Note:Note correct identification of camshafts.Inlet side : three grooves after thrust bearingExhaust side: two grooves afte

Strona 341

11.44Installing timing chain•Turn the camshaft so that the grooves on the ends are vertical in relation to the cylinder head at the rear.•The grooves

Strona 342 - LT610020

11.45•Press serrated washer (8) with eccentric shoul-der into the chain guide rail spacing bushing by a small amount.•Turn the serrated washer until t

Strona 343 - LT610030

33 Rear wheel drive ... 33.134 Brakes ...

Strona 344 - LT610040

11.46Installing intermediate flangeInstalling freewheel•Insert the freewheel into the crankcase with the helical-cut gearwheel leading.•Oil the needle

Strona 345 - LT610050

11.47Installing timing case cover•Apply a thin coat of 3-Bond 1209 to the sealing faces, which must be free from oil and grease.•Pass the wires for th

Strona 346 - LT610070

11.48Installing cover for Hall-effect transmit-ter•Install the wire for the Hall-effect transmitter with rubber grommet (arrow) in the timing case cov

Strona 347

11.49Installing cylinder head cover•Insert reamed bolt (arrow), BMW No. 11 1 980, into inner front hole.•Press centering pin, BMW No. 00 5 500, into m

Strona 348

11.50Installing engine•Attach hoist, BMW No. 00 1 510, to the oil sump.•Set the engine down on the hoist platform.•Release the engine mounting at the

Strona 349 - 62 Instruments

11.51•Connect the engine wiring harness (coolant stub pipe, throttle position sensor, CO detector, injec-tors, air cleaner housing).•Attach cable stra

Strona 350

11.52Checking/adjusting valve clear-ancese Caution:Never unscrew the spark plugs before measuring valve clearances. Particles of oily soot could be-co

Strona 351

12.1Contents Page12Technical data...

Strona 353 - LT620010

12.312Technical data K 1100 LT K 1100 RSStarterType Permanent magnet motorGear ratio 27 : 1Output kW 0,7AlternatorType Three-phase alternator with in

Strona 354 - LT620020

00.1Contents Page00Tightening torque ...

Strona 356 - LT620080

12.5Removing and installing Hall gener-ator•Disconnect ground lead of battery and insulate.•Remove radiator cowling.•Remove fuel tank.•Disconnect Hall

Strona 357 - LT620100

12.6Adjusting ignition timing•Remove radiator cowling.•Remove bottom left fairing.•Remove fuel tank.•Disconnect plug connection on Hall generator lead

Strona 358 - LT620110

12.7•Loosen base plate (1) and turn to the left or right until diode (2) on ignition setting device goes out.L Note:Ignition timing adjustmentTurn to

Strona 359 - 63 Lights

12.8Removing and installing ignition coils•Disconnect earth (ground) lead of battery and in-sulate.•Remove top (1) and bottom (2) ignition coil cover.

Strona 360

12.9Removing and installing ignition output stage•Remove left battery bracket.•Disconnect earth (ground) lead of battery.•Remove ignition coils.•Remov

Strona 361

12.10Removing and installing alternator•Remove right battery panel.•Remove Motronic control unit.•[ABS I] Remove ABS control unit.•Remove battery.•Rem

Strona 362

12.11Disassembling and assembling alternatorAlternator [only LT up to 1992 model year]•Remove damper elements (1)•Remove coupling housing (2) with hol

Strona 363 - LT630010

12.12•Remove regulator (8) with carbon brushes.•Carefully lift out armature (9) together with bear-ing (10).•Remove bearing (10) from armature shaft.•

Strona 364 - Adjusting headlights

12.13Checking armature for short to earth•Measure resistance between slip rings and ar-mature.L Note:The resistance must be infinitely large.Measureme

Komentarze do niniejszej Instrukcji

Brak uwag